Wheeler Indiana Concrete Replacement Companies

Patching a Wheeler driveway stops making sense once cracks come back through the same spots after a winter. Full replacement is the call when the slab has broken into pieces and the patches don’t stay put. Concrete Replacement Companies in Wheeler see this on older drives every spring. So we look at the whole slab before we talk about another patch.

Decades-old drives on Wheeler houses crack and scale through northwest Indiana winters. Water gets into small cracks. Then it freezes and the crack opens wider. After enough seasons the surface scales and the edges crumble near the street. Because road salt rides in on tires, the surface often scales off in flakes. We’ve pulled up slabs that looked fine from the road and were hollow underneath.

What We Check Before Concrete Replacement Companies in Wheeler Replace a Drive

New broom-finish driveway from a garage to the road - Concrete Replacement Companies in Wheeler

When a homeowner calls, we walk the drive from the garage to the road. We look for cracks that run the full width and for spots that rock when you step on them. Patches that have popped loose show the old concrete is moving in separate pieces. So those spots tell us whether another repair will hold. For example, we can cut out a single corner break and pour it back. After the cracks connect across the slab, a new patch usually fails in the next hard freeze.

We also check the base under the concrete and the way water leaves the drive. A slab that has sunk at the garage or lifted at the apron needs more than surface work. Because we do concrete removal and tear-out work, we can take the old drive out. We set a new base before the pour so the new slab sits on something solid. After enough winters, decades-old drives on Wheeler houses crack through, and patches stop holding. That’s when we switch the job to a full replacement and include the tear-out.

Get A FREE Proposal Today!

Concrete Replacement Companies in Wheeler Handle the Full Tear-Out

Crew breaking out an old driveway slab - Concrete Replacement Companies in Wheeler

Once patches no longer hold, we treat the drive as a replacement. We saw-cut where the new concrete meets the garage and along the street edge. A cracked service walk can come out in the same pass if it has failed with the drive. Then we break out the old slab and haul it away. After the base is graded, we set forms and pour. So the new drive runs as one slab from the garage door out to the road.

A lot of Wheeler houses have an upper walk that cracked along the same line as the drive. When we’re already set up for the replacement, we can replace that walk in the same visit. We can pour a spalling garage floor while the crew and the forms are there. Residential concrete covers pads and full drives on these Wheeler jobs. We’ll work with you on the finish you want, a broom surface or a colored mix.

Cabe’s Concrete is a family owned and operated company, and we’ve worked here since 2006. Our staff have a wealth of experience in the field. You can look through finished jobs in our Photo Gallery. Our About Us page covers how the crew works on a replacement. The page for our concrete replacement work covers the tear-out and the new pour.

People call us about the same crack on a Wheeler drive after it was filled more than once. On past jobs, patches came out in one piece after a single winter. So we tell you when another patch won’t hold. Concrete Replacement Companies in Wheeler take the old drive out and pour a new one as a single job. Because we rebuild the base, the new slab sits on graded stone.

Driveway Edges and Concrete Replacement Companies in Wheeler

Freshly formed concrete apron beside a garage - Concrete Replacement Companies in Wheeler

The apron is the spot on a Wheeler drive that breaks up first. Tires turn there, and meltwater from the street sits along the edge. When that edge breaks into chunks, a patch at the street rarely lasts. Concrete Replacement Companies in Wheeler form that apron with the new drive. We slope the new apron so water can leave the slab. Then we tie the pour into the walks that stay, if those walks are still sound.

Where the drive meets a curb, we pour up to that curb and tool the joint. When the curb is part of the same job, we form it with the drive. We cut a clean edge where the concrete meets gravel or the road. The crew tools the joints while the concrete is still workable. Then we check the edges before we leave the site.